This flag holder bar can be installed or detached from a trailer hitch equipped bike in seconds. Included is the chromed bar, chrome plugs and one flag holder socket. One or two more sockets can be added (sold separately) to accommodate up to three flags. The sockets accommodate up to 1 1/4” poles and are machined at a 150° angle to their bases. They can be rotated and tightened to display your flags angled to the rear, sides, diagonally or any combination of these. All components are machined from aircraft quality aluminum and steel, then polished to a flawless finish and triple chrome plated.

NOTE: Hardware mounting kit must be ordered separately to make a complete flag holder assembly.
HWK010 - for any motorcycle with an existing trailer hitch.

PF930 Add-on 4-5 Flag Holder: Three flags not enough? This large flag holder bar accommodates anywhere from one to five flags for an awe-inspiring spectacle of pride. It will replace the smaller bar on model PF1000, PF900 or PF910. Additional flag holder sockets (PF920) sold separately.

This flag holder bar can be installed or detached from the RIVCO receiver bracket in seconds. Included is the chromed bar, chrome plugs and one flag holder socket. One or two more sockets can be added (sold separately) to accommodate up to three flags. The sockets accommodate up to 1 1/4” poles and are machined at a 150° angle to their bases. They can be rotated and tightened to display your flags angled to the rear, sides, diagonally or any combination of these. All components are machined from aircraft quality aluminum and steel, then polished to a flawless finish and triple chrome plated.

NOTE: One of the following model specific mounting and hardware sets shown below must be ordered separately to make a complete flag holder assembly.
HWK010 - for any motorcycle with an existing trailer hitch.
HWK015 - For all (2008 and earlier) Harley-Davidson FL & FLH models
HWK020 - For all (2009 & newer) Harley-Davidson FL & FLH models
PF910-4 - For Road Kings with Saddlebag Rails. These brackets to provide some necessary clearance when adding our Parade Flag Holder. Sold in pairs.

PF930 Add-on 4-5 Flag Holder: Three flags not enough? This large flag holder bar accommodates anywhere from one to five flags for an awe-inspiring spectacle of pride. It will replace the smaller bar on either model PF900 or PF910. Additional flag holder sockets (PF920) sold separately.

Note: With a bit of workmanship, other riders have used this on other big cruisers like the Vulcan 2000. If not sure, simply get a trailer hitch kit and then you can use the the hardware kit for trailer hitches to attach the holder to your bike.

The collapsible telescoping flag pole goes from 18" (small enough to fit in most saddlebags) to 6 1/2 feet in seconds with positive twist locks inside each section. The bottom section is 1 1/4" in diameter and slides snugly into all our parade flag holders. Made from lightweight and strong aircraft aluminum tubing. It has a durable silver anodized finish, quick release flag mounting clips and is topped off with an attractive gold ball. NOTE: This flag pole is meant for parade use only and is recommended for use at a maximum speed of 25 mph. (Due both to the adverse handling that a flag can cause at higher speeds as well as the load limit of the flag pole).

Available Flags:

PFFLAG: 36" x 60" (3' x 5') American Flag. Compatible with RIVCO Telescoping Flag Pole (PFPOLE). Lightweight yet sturdy nylon construction and bright colors combine to create a moving display of patriotism.

PFPOW: 36” x 60” (3’ x 5’) flag, displaying the POW-MIA symbol. Compatible with the RIVCO Telescoping Flag Pole.

PFSGA: 36” x 60” (3’ x 5’) flag, portraying the American eagle with the U.S. flag and POW-MIA symbol. Compatible with RIVCO Telescoping Flag Pole. Polyester construction features two brass grommets and heavy stitching.